DE/DTE Series

Overview

Type: forming, eccentric presses
Press Capacity: 300-3,375 tons
Part Size: medium to large
Slide Kinematics: mechanical
Application: cutting, blanking, bending, punching, stamping, embossing & forming

Description

The mechanical drive of the DE and DTE Series is ideal for flat and semi-flat parts due to its sinusoidal slide motion curve. The Series can be installed as a single press in progressive or transfer mode or as a fully automated press line.

Features & Benefits

Proven and continuously optimized technology for reliable production processes.
The mechanical drive of the DE and DTE Series is ideal for cutting, punching, bending, and stamping operations.
The solid, low-stress annealed press bodies are FEM-calculated and optimized by “hot-spot analysis” areas subject to higher loads.
Presses in tie rod design are connected to a rigid frame via hydraulically pre-stressed tie rods.
The outside located pressure points, as well as an 8-fold slide guiding system, absorb off-center loads, spare press, and dies to ensure consistent part quality.
The automatic centralized lubrication system increases productivity and availability.
Availability of an extensive range of optional equipment (i.e., die cushions, pneumatic ejectors, or moving bolsters for a faster die change).

Technical Specifications

Metric

DE2P Series

Model		DE2P-400	DE2P-600	DE2P-800	DE2P-1000	DE2P-1200	DE2P-1400
Press Capacity	ton	400	600	800	1000	1200	1400
Rated Tonnage Point	mm	13	13	13	13	13	13
Stroke Rate	spm	70	50	40	35	30	27
Stroke Length	mm	700	700	700	700	700	700
Slide Adjustment	mm	600	600	600	600	600	600
Die Height	mm	1200	1200	1200	1200	1200	1200
Slide Dimension	mm	2800x1600	2800x1600	3000x1800	3000x1800	3000x1800	3000x1800
Bolster Dimension	mm	2800x1600	2800x1600	3000x1800	3000x1800	3000x1800	3000x1800

* SDAU = slide stroke down, adjustment up | 2P = 2-point design | 4P = 4-point design | Subject to technical modifications

DE4P Series

Model		DE4P-400	DE4P-600	DE4P-800	DE4P-1000	DE4P-1200	DE4P-1500	DE4P-2000	DE4P-2500
Press Capacity	ton	400	600	800	1000	1200	1500	2000	2500
Rated Tonnage Point	mm	13	13	13	13	13	13	13	13
Stroke Rate	spm	70	50	40	35	30	27	27	27
Stroke Length	mm	700	800	800	800	800	800	800	800
Slide Adjustment	mm	600	600	600	600	600	600	600	600
Die Height	mm	1300	1300	1300	1300	1300	1300	1300	1300
Slide Dimension	mm	3200x2000	3200x2100	3200x2100	3400x2300	3400x2300	4500x2500	4500x2500	4500x2800
Bolster Dimension	mm	3200x2000	3200x2100	3200x2100	3400x2300	3400x2300	4500x2500	4500x2500	4500x2800

* SDAU = slide stroke down, adjustment up | 2P = 2-point design | 4P = 4-point design | Subject to technical modifications

DTE Series

Model		DTE2-500	DTE2-1000	DTE2-1500	DTE4-1500	DTE4-2000	DTE4-2500	DTE4-2600
Press Capacity	ton	500	1000	1500	1500	1500	2000	2600
Rated Tonnage Point	mm	13	13	13	13	13	13	13
Stroke Rate	spm	50	35	27	27	27	27	27
Stroke Length	mm	450	600	600	700	700	800	800
Slide Adjustment	mm	300	600	600	600	600	600	600
Die Height	mm	1200	1200	1200	1200	1200	1200	1200
Slide Dimension	mm	3000x1200	4000x1700	4500x1700	5500x2500	6300x2400	6300x2400	6300x2400
Bolster Dimension	mm	3000x1200	4000x1700	4500x1700	5500x2500	6300x2400	6300x2400	6300x2400

* SDAU = slide stroke down, adjustment up | ST = standard | HS = high-speed | LS = long stroke | Subject to technical modifications